Recent Activity

Activity stream for all registered members at Flooring Forum - DIY and Professional.

Help Support Flooring Forum by donating:

  1. zannej replied to the thread What did you do today?.

    Thanks, Highup. I'll have to try that. I'm still feeling under-the-weather and hoping whatever virus my brother brought home isn't going...

    Jan 24, 2020 at 8:04 PM
  2. zannej liked highup's post in the thread What did you do today?.

    I'll toss a motivational idea at ya Zan. Starting anything is a problem I have too. One project.... no problem. 20 projects and I...

    Jan 24, 2020 at 8:01 PM
  3. highup replied to the thread What did you do today?.

    I'll toss a motivational idea at ya Zan. Starting anything is a problem I have too. One project.... no problem. 20 projects and I...

    Jan 24, 2020 at 7:01 AM
  4. zannej replied to the thread What did you do today?.

    Good to hear from you, Tom. I just realized I have a friend who lives either in or near Lancaster. His family fled from China to Vietnam...

    Jan 24, 2020 at 4:30 AM
  5. zannej liked Floorist's post in the thread What did you do today?.

    Glad to see you back.

    Jan 24, 2020 at 4:02 AM
  6. zannej liked Tom Picciani's post in the thread What did you do today?.

    Haven't been on the forum in a while and wanted to check in. Glad to hear from the usual suspects. The Coretec is holding up very well...

    Jan 24, 2020 at 4:02 AM
  7. Floorist replied to the thread What did you do today?.

    Glad to see you back.

    Jan 23, 2020 at 6:31 PM
  8. Tom Picciani replied to the thread What did you do today?.

    Haven't been on the forum in a while and wanted to check in. Glad to hear from the usual suspects. The Coretec is holding up very well...

    Jan 23, 2020 at 6:19 PM
  9. highup replied to the thread Best tool for Undercutting existing baseboard.

    On small pieces, a small diameter nail set or drift punch card drive the fastener far enough in so the piece comes off without splitting.

    Jan 23, 2020 at 5:29 PM
  10. zannej liked DJS819's post in the thread Best tool for Undercutting existing baseboard.

    Joining the bandwagon, I replace baseboards for any floor I install (tile or wood).

    Jan 23, 2020 at 5:45 AM
  11. zannej liked havasu's post in the thread Best tool for Undercutting existing baseboard.

    and that visible gap would look horrendous, since you lay the thinset, slide in the tile, then push down to adhere properly. Spend a...

    Jan 23, 2020 at 5:45 AM
  12. zannej liked highup's post in the thread Best tool for Undercutting existing baseboard.

    I don't do tile, but I'd assume it might be harder to fit the tile evenly under the base board than just remove it then reinstall it on top.

    Jan 23, 2020 at 5:44 AM
  13. zannej liked DarisMulkin's post in the thread Best tool for Undercutting existing baseboard.

    Devils advocate here. But now the baseboard would be higher than all the rest in the house if applied after. P.S. I'd remove it also.

    Jan 23, 2020 at 5:44 AM
  14. zannej liked havasu's post in the thread Best tool for Undercutting existing baseboard.

    The problem with undercutting the baseboard is now it would be shorter that the other baseboards in the house.

    Jan 23, 2020 at 5:44 AM
Loading...