Flooring pictures

Flooring Forum - DIY & Professional

Help Support Flooring Forum - DIY & Professional:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
filler

16174737_10210425352805460_1459529584117391454_n.jpg
 
Looks like he just stacked all his leftover cuts end to end.
I'm doing a rental right now. There were 9 pieces of pad in a 12' by 13' bedroom, 11 pieces of pad in a 9'6" by 13' bedroom and in one corner of the living room, about a 4' X 7' area including a 2'X3' closet I counted 13 pieces of pad....... one inch trips, 2 inch by 6 inch strips, and even a single 1 inch piece.
My guess was the installer was using every single scrap and trying to retain the rest of the pad he was sent with for his own use. There are 8 units. I'm betting he kept a full roll for himself.
 
Looks like he just stacked all his leftover cuts end to end.
I'm doing a rental right now. There were 9 pieces of pad in a 12' by 13' bedroom, 11 pieces of pad in a 9'6" by 13' bedroom and in one corner of the living room, about a 4' X 7' area including a 2'X3' closet I counted 13 pieces of pad....... one inch trips, 2 inch by 6 inch strips, and even a single 1 inch piece.
My guess was the installer was using every single scrap and trying to retain the rest of the pad he was sent with for his own use. There are 8 units. I'm betting he kept a full roll for himself.

Some stores at least here will under cut you on yardage of the pad by 10%. They say if you have any leftover pieces you better hang onto them for when you are short. I used up pieces to an extent and had leftovers to make into full rolls for me. But there were times I had to use carpet scraps to finish out a closet or a corner.

Daris
 
I always do one step the way is should be done with just a few staples to show the customer the difference in the look.
 
hmmm...Think I would have covered the stringer, if it was ok with the customer.
I think so too. The carpet on the riser where it contacts upper side of the stringer looks a bit uneven or over stapled. I bet if careful, a hot glue gun might have performed miracles. Might have taken a bit more time per step to achieve a little more consistency and perfection. Depending on the job and price, spending the extra time to achieve that perfection is not always possible nor expected.
If I could end that job at 2pm and have the rest of the day off, or loose my ass time wise and work till 5 or 6 to make it as perfect as possible. The day is toast if it ends at 2 pm or at 6 pm, so why not go the extra mile and spend the time to gain a customer for life and referrals from them?
The camera and harsh lighting angles probably make what I see look worse than it actually is. It's not a bad job. I just see what looks like pock marks from that stapler. I'm a whiny picky old geezer as you know. :D
 
I'd dug down a lot deeper than that............ not earthworm deep but if it's fixable, I'll do it. (not at the shops estimate) They don't usually see stuff that needs this much fixing anyhow. I find out how bad the repair is when I get there and start diggin'.
 
Last edited:
That stringer is just wrong but I would have covered it too.

The place looks pretty 'rustic'. I'm betting the rest of the place has some unusual construction features. I'm thinking now that you mention it...... that stringer should have looked like an oversized skirt board instead of the step running over onto it.
 
The installer only made $80 for the job. HO won't pay to do anything else. Some other installers are giving the guy grief because he did not ramp it. The difference is 5 inches. How in the hell would you ramp 5 inches and not make the carpet installation look like crap? If the installer even added a threshold, it would come out of his $80. IMHO, HO got what they paid for.
 

Latest posts

Back
Top